Strength Concrete Glue TK2

A kind of emulsion material for making adhesive mortars on concrete surfaces, as a strong adhesive intermediate material to increase the adhesion strength and reduce the permeability of concrete or mortar and repairs of concrete and cement surfaces has been produced.

Standards:

ASTM , C 1042 , C1059
C 1440 , BS 6319

Physical State:

Emulsion

Color:

White

Special Weight:

0.8 ± 0.02

Chlorine Ion:

None

Acidity (PH):

8.5 ± 0.5

Adhesion of concrete surface and modified mortar:

Adhesion of new concrete to old:

Ability to dissolve in water before drying:

Do have

Solubility in water after drying:

Do Not Have

Packing:

It is available in 1 , 4 , 15 gallons.

The method of making construction lining mortar and universal coating

Preparation of construction mortar according to the formula: (one cup of TK2 + one or two cups of water) the mixture and solution obtained as mortar water in dry mortar ready to the formula (zero to 2.5 mm sand 15 kg + cement 5 kg) as needed be added Preparation of mortar according to the amount of work should be mixed up to one hour.
This mortar can be traditionally applied as a lining coating with a maximum thickness of 15 mm on concrete and brick surfaces.
For greater thicknesses, it is repeated with a time interval of at least 4 hours.
The above-mentioned mortars can be used for local repairs and general coating.

Technical services

Aryashimi’s technical department is ready to cooperate and provide services in order to provide technical advice and how to use its products correctly.

Storage Period

It can be used for up to 12 months if kept in the recommended conditions and in the original packaging.

Maintenance

It should be kept away from cold and frost and direct sunlight and at a temperature of +5 to +35 degrees Celsius.

Benefits of use

اIncreasing the adhesion strength of mortar to old concrete without using metal nets
Reduction of cracking due to lack of shrinkage and proper flexibility
High resistance against freezing cycles of deicing salts
Reduced permeability and no corrosive properties
Increasing tensile and bending resistance and abrasion resistance
Mortars made with TK2 can be used for up to 30 minutes.

Consumption

800 grams of TK2 cement mortar should be used per square meter with a thickness of one centimeter.
300 grams of TK2 should be used for each square meter with a thickness of 3 mm.

Practical Items

Preparation of mortar and coatings for:
Concrete wall and floor surfaces of various factories, warehouses, parking lots
Substructure for flooring
Repair of surface damage
Facade construction and implementation of exposed surfaces
Adhesion agent in putty powder for smoothing exposed concrete surfaces and underlaying epoxy, acrylic, polyurethane paints.
Preparation of adhesive mortar for overall smoothing of the concrete surface instead of using metal grids
Reinforcement of powder tile adhesive SA100-SA90
Preparation of stone putty to fill stone pores after installation or in quarries
Preparation of adhesive mortars with sand, cement and stone soil for ceramic and stone installation

Surface Preparation

The surface under the work should be removed from any pollution, grease, dust and surface decay.
Loose and porous areas should be completely removed by mechanical methods.

Safety Tips

Avoid direct and permanent contact of this substance with the skin.
As a chemical substance, protective gloves and safety glasses should be used to avoid contact with skin or eyes.
In case of accidental contact with skin or eyes, wash with plenty of water.

The method of making local and global softening mortar

Preparation of smoothing coating according to the formula: (three cups of siliceous soil + one cup of cement) instead of water, add the required amount of solution (one cup of TK2 + one or two cups of water) to prepare the smoothing mortar.
The resulting mortar with a maximum thickness of 3 mm is applied and smoothed on the lining surface after primer with a metal trowel.
In places where the surface needs to be leveled, immediately after the execution, you can lay the tip or acrylic mesh on the surface and trowel until the mortar comes out of the mesh opening and create a coating on the surface.
To increase the safety factor, acrylic mesh can be used locally or globally.
After coating, the working surface should be kept moist for 5 days, away from sunlight, and after 10 days, the above surface can be used.